Diesel 101 

Fuel

 

 

Air makes the potential — fuel makes the power. From the tank to the injector tip, your fuel system decides how much power the engine can safely make and how long it lives doing it. This is everything FUEL: injectors, lift pumps, injection pumps, rails, and even what you're pouring in the tank.

Inside Fuel

Power is made of fuel and air

Open a topic to see how we think about it — what each part does, what fails first, and which upgrades protect your engine while feeding bigger power on a Cummins, Duramax, or Power Stroke.

 

The most precise part in your engine — and the most expensive to neglect. Modern common-rail injectors fire multiple times per combustion event at pressures north of 26,000 PSI, metering fuel in microns. When they wear, you get hard starting, white smoke, rough idle, and fuel dilution in the oil — ignore it long enough and a stuck injector can melt a piston. For performance, larger-flow injectors supply the fuel big turbo setups demand, but they need tuning to match and they're sized in stages: a tow rig wants a mild upgrade for clean delivery, while a competition build can run much larger nozzles. Whatever the level, buy quality remans or new — cheap injectors are the most expensive injectors you'll ever buy.

Ask About Injectors 

The single best insurance policy for a modern diesel. The lift pump moves fuel from the tank to the injection pump. Factory systems on many trucks (especially Duramax, which ran no factory lift pump for years) leave the high-pressure pump pulling fuel uphill through restrictive lines. An aftermarket lift pump system — like the AirDog and FASS systems we stock — delivers steady positive pressure, and just as importantly, it filters the fuel down to a few microns and strips out water and air before it ever reaches the expensive parts. Clean, air-free, properly pressurized fuel is the difference between an injection system that lasts 300,000 miles and one that fails at 80,000. If you do one thing from this page, do this.

Ask About Lift Pumps 

The heart of the fuel system — and on some trucks, its weak point. The injection pump generates the extreme pressure common-rail systems run on. The Bosch CP4 pump found in 2011+ Duramax and Power Stroke trucks has a known failure mode: when it comes apart, it sends metal through the entire fuel system — injectors, rails, lines, tank — turning a pump failure into a five-figure repair. The industry's answer is the CP3 conversion: swapping in the older, proven CP3 pump (like the S&S Diesel Motorsport kits we carry) for bulletproof reliability, often for less than the cost of one CP4 failure. On Cummins trucks the CP3 came standard on most years. If you own a CP4 truck, this conversion is the highest-value reliability upgrade on the market.

Ask About CP3 Conversion 

The highway between the pump and the injectors. The common rail is a pressure reservoir that feeds every injector evenly, and the lines that feed it live under brutal pressure cycles every second the engine runs. On a stock truck the factory rail and lines do their job quietly. On a high-performance build, rail pressure stability becomes the limiting factor — upgraded rails, feed lines, and rail fittings keep pressure consistent when larger injectors are pulling hard. This is also where leaks show up first on high-mileage trucks: wet spots around rail fittings or injector lines are a fix-now item, not a watch-it item, at these pressures.

Ask About Rails & Lines 

What you pour in matters as much as what you bolt on. Ultra-low sulfur diesel (ULSD) is the standard at the pump, but it carries less natural lubricity than the fuel these injection systems were designed around — a quality additive restores lubricity, adds cetane for cleaner combustion, and protects the pump and injectors you just read about. Biodiesel blends (B5–B20) are common and fine in most modern trucks within manufacturer limits, but they absorb more water and can gel sooner in the cold — something to plan around in a Pacific Northwest winter. And if you fuel up in freezing country, an anti-gel treatment is cheap insurance against a truck that won't start on the coldest morning of the year.

Ask What We Run 

Shop The Category 

Our Picks For Fuel

 

 

The lift pumps, injectors, and fuel-system parts we'd put on our own trucks — matched to your year, make, and model. Don't see your setup? Call the shop and we'll track it down.

Title

Injectors

Products
View product
Dodge 07.5-18 6.7L Individual Stock Brand New Injector Dynomite Diesel
Price
$584.25
View product
Ford 6.7L 15-18 Brand New 45 Percent Over Injector Set Dynomite Diesel
Price
$4,940.00
View product
Ford 6.7L 11-14 Individual Stock Reman Injector Dynomite Diesel
Price
$451.25
Title

Fuel Add-ons

Products
View product
Dodge 94-98 5.9L 12 Valve Fuel Plate Kit Dynomite Diesel
Price
$166.25
View product
Fuel Sump Universal AirDog
Price
$175.00
View product
Fuel System 150GPH FP-150-4G 1998.5-2004 Dodge Cummins AirDog
Price
$770.00

Keep learning about diesel Choose a new category

Done here? Jump straight into the next topic.

 

Drop Us A Line

 
⚑

Find Us

1420 South Henderson Street
Seattle, WA 98108

☉

Watch Us

Follow along for builds, shop life, and diesel content.

Hours Mon–Fri: 10:00 AM – 6:30 PM Sat–Sun: Closed